The APDTY 140067 engine oil pan assembly is a complete aluminum replacement for 2015-2022 Chevrolet Colorado and 2015-2020 GMC Canyon 4WD models equipped with the 2.5L (L4 153 / 2457cc) engine and 16-bolt pan design. This assembly includes the oil pan, drain plug, drain plug gasket, and oil level sensor, allowing you to replace a damaged, rusted, or leaking pan without sourcing individual components separately. It directly replaces OE part numbers 25202729 and 12667012.
Key Takeaways
- Complete oil pan assembly for 2015-2022 Colorado 4WD and 2015-2020 Canyon 4WD with 2.5L engine (16-bolt design)
- Includes oil pan, drain plug, drain plug gasket, and oil level sensor
- Replaces OE part numbers 25202729 and 12667012
- Aluminum construction for durability and heat dissipation
- Direct-fit replacement for damaged or leaking oil pans
Buy APDTY 140067 directly from APDTY
What Does the Engine Oil Pan Do?
The engine oil pan serves as the reservoir that holds your engine's oil supply when the vehicle is off or idling. Bolted to the bottom of the engine block, the pan collects oil draining back from the crankshaft, pistons, and cylinder head, allowing the oil pump to draw from this reservoir and circulate lubricant throughout the engine. The oil level sensor mounted in the pan monitors oil quantity and warns the driver if the level drops dangerously low.
A damaged or corroded oil pan can leak oil onto the ground, leading to low oil levels, potential engine damage, and environmental contamination. The APDTY 140067 assembly provides a complete, factory-quality replacement to restore proper oil containment and monitoring.
What Are the Symptoms of a Damaged or Leaking Oil Pan?
Common signs that your oil pan needs replacement include:
- Oil puddles or spots under the vehicle after parking, especially near the front-center of the engine bay
- Low oil level warnings on the dashboard or frequent need to add oil between changes
- Visible damage to the pan from road debris, curb strikes, or corrosion (common in salt-belt states)
- Oil level sensor faults or erratic oil pressure readings caused by a failing sensor or damaged sensor mounting boss
- Stripped drain plug threads that prevent proper torque and cause leaks at oil changes
If you notice any of these symptoms, inspect the oil pan and surrounding gasket area. A cracked, dented, or corroded pan requires replacement to prevent engine oil starvation and costly internal damage.
Which Vehicles Does APDTY 140067 Fit?
Based on verified fitment data, the APDTY 140067 oil pan assembly is compatible with the following vehicles equipped with the 2.5L (L4 153 / 2457cc) engine and 16-bolt oil pan design:
| Year Range | Make | Model | Drive Type | Engine | Pan Design |
|---|---|---|---|---|---|
| 2015-2022 | Chevrolet | Colorado | 4WD | L4 153 2.5L (2457cc) | 16 Bolt |
| 2015-2020 | GMC | Canyon | 4WD | L4 153 2.5L (2457cc) | 16 Bolt |
Important: This oil pan is designed specifically for 4WD (four-wheel drive) models with the 16-bolt pan configuration. Two-wheel drive models and vehicles with different engine sizes or bolt patterns require different oil pans. Always verify your vehicle's year, model, engine size, and drive type before ordering. If you are unsure whether this part fits your specific vehicle configuration, check the live compatibility chart on the product page or contact APDTY customer support.
What's Included and What Are the Specifications?
The APDTY 140067 is a complete assembly that eliminates the need to source individual components separately. Here's what you receive:
| Component | Description |
|---|---|
| Engine Oil Pan | Aluminum construction, 16-bolt mounting pattern |
| Drain Plug | New magnetic drain plug (if applicable) or standard plug |
| Drain Plug Gasket | New crush washer or gasket for proper drain plug seal |
| Oil Level Sensor | New sensor for accurate oil level monitoring |
Specifications:
- Material: Aluminum alloy for lightweight strength and efficient heat dissipation
- Bolt Pattern: 16-bolt design (matches OE configuration)
- OE Replacement Numbers: 25202729, 12667012
- Capacity: Matches OE oil pan volume (typically 5-6 quarts system capacity including filter)
The aluminum construction resists corrosion and provides superior durability compared to steel pans, especially in climates where road salt and moisture accelerate rust.
How Do You Install an Oil Pan Assembly?
Oil pan replacement is an intermediate-level repair that requires basic mechanical skills, a lift or jack stands, and appropriate hand tools. Always consult your vehicle's factory service manual for torque specs and detailed procedures. General installation steps include:
- Safety first: Park on a level surface, engage the parking brake, and use jack stands rated for your vehicle's weight. Never work under a vehicle supported only by a jack.
- Drain the engine oil: Warm the engine slightly to thin the oil, then drain completely into an approved container. Dispose of used oil properly at a recycling center.
- Remove the old oil pan: Disconnect the oil level sensor wiring harness. Remove all pan bolts in a criss-cross pattern, starting from the outside and working inward. Gently pry the pan loose if gasket adhesive is present. On 4WD models, you may need to remove or lower the front differential or crossmember for clearance.
- Clean the mounting surface: Use a gasket scraper and solvent to remove all old gasket material and RTV sealant from the engine block mating surface. Ensure the surface is clean, dry, and free of debris.
- Install the new oil pan: Apply a thin bead of RTV gasket maker to the pan flange if specified by your service manual (some pans use a gasket only, others require RTV). Position the new APDTY 140067 pan and hand-start all 16 bolts. Torque in a criss-cross pattern to factory specs (typically 15-20 ft-lbs, but verify with your manual).
- Connect the oil level sensor: Plug in the wiring harness to the new sensor included with the assembly.
- Install the drain plug: Thread in the new drain plug with the new gasket or crush washer. Torque to spec (usually 15-25 ft-lbs).
- Refill with engine oil: Pour in the correct type and quantity of oil for your 2.5L engine (consult owner's manual). Install a new oil filter.
- Check for leaks: Start the engine and let it idle for several minutes. Inspect the pan, drain plug, and sensor for any signs of leakage. Shut off the engine, wait a few minutes, and recheck the oil level.
Important: Some 4WD models require removal or repositioning of front suspension or drivetrain components for oil pan access. If you are not comfortable with this level of repair, seek assistance from a qualified mechanic.
Frequently asked questions
Does APDTY 140067 fit 2WD (two-wheel drive) Colorado or Canyon models?
No. The APDTY 140067 is designed specifically for 4WD models with the 2.5L engine and 16-bolt pan design. Two-wheel drive models use a different oil pan configuration.
Do I need to apply RTV sealant when installing this oil pan?
Consult your vehicle's factory service manual. Some applications require a thin bead of RTV gasket maker on the pan flange; others use a gasket only. Follow OE specifications for your specific year and model.
What OE part numbers does the APDTY 140067 replace?
This assembly replaces GM OE part numbers 25202729 and 12667012.
Can I reuse the old drain plug and oil level sensor?
It is not recommended. The APDTY 140067 includes a new drain plug, gasket, and oil level sensor for a reason—reusing old components can lead to leaks or sensor faults. Always install the new components provided with the assembly.
A damaged or leaking oil pan puts your engine at risk every time you drive. The APDTY 140067 engine oil pan assembly provides a complete, factory-quality replacement for 2015-2022 Chevrolet Colorado and 2015-2020 GMC Canyon 4WD models with the 2.5L engine and 16-bolt design. With the oil pan, drain plug, gasket, and oil level sensor all included, you get everything needed to restore proper oil containment and monitoring in one box. Stop the leak, protect your engine, and restore peace of mind—order the APDTY 140067 today from autopartsdirecttoyou.com.