The APDTY 137292 ABS wheel speed sensor is a direct-replacement front left or front right sensor designed to restore proper anti-lock braking and traction control function in multiple GM and Suzuki vehicles. When a front wheel speed sensor fails, drivers typically see an illuminated ABS warning light, disabled traction control, and loss of anti-lock brake assist—issues this sensor is engineered to fix.
Key Takeaways
- Direct replacement front ABS wheel speed sensor for 2007-2015 Chevrolet, Pontiac, Saturn, and Suzuki models
- Fits either front left or front right position on compatible vehicles
- Restores ABS and traction control function when original sensor fails
- Replaces multiple OE part numbers including GM 96626078, 19208998, and Suzuki 56210-78J00
- Compatible with 2012-2015 Captiva Sport, 2007-2009 Equinox, 2007-2009 Torrent, 2008-2010 Vue, 2007-2009 XL-7
Buy APDTY 137292 directly from APDTY
What Does the ABS Wheel Speed Sensor Do?
The ABS wheel speed sensor monitors the rotational speed of each wheel and sends that data to the vehicle's ABS control module. The module uses this information to:
- Detect when a wheel is about to lock up during hard braking
- Modulate brake pressure to prevent wheel lockup and maintain steering control
- Enable traction control and stability control systems
- Provide speed data for speedometer and cruise control functions (in some systems)
Each wheel typically has its own speed sensor. The APDTY 137292 specifically replaces the front left or front right sensor on the vehicles listed in the compatibility section below.
What Are the Symptoms of a Failed Front Wheel Speed Sensor?
When a front ABS wheel speed sensor fails or sends erratic signals, you'll typically experience one or more of these symptoms:
- ABS warning light illuminated on the dashboard
- Traction control light on or traction control disabled message
- Stability control light on (if equipped)
- Loss of ABS function—brakes work normally but without anti-lock assist during hard stops
- Speedometer or odometer issues in some cases (depending on vehicle design)
- Stored diagnostic trouble codes such as C0035, C0040, C0045, C0050 (wheel speed sensor circuit malfunction)
These symptoms occur because the ABS module cannot accurately determine wheel speed when the sensor fails. The system defaults to a fail-safe mode, disabling ABS and traction control to prevent false activation.
Which Vehicles Does APDTY 137292 Fit?
Based on verified fitment data, the APDTY 137292 front ABS wheel speed sensor is compatible with the following vehicles:
| Year Range | Make | Model | Position |
|---|---|---|---|
| 2012-2015 | Chevrolet | Captiva Sport | Front Left or Front Right |
| 2007-2009 | Chevrolet | Equinox | Front Left or Front Right |
| 2007-2009 | Pontiac | Torrent | Front Left or Front Right |
| 2008-2010 | Saturn | Vue | Front Left or Front Right |
| 2007-2009 | Suzuki | XL-7 | Front Left or Front Right |
Important: This list reflects the fitment data provided with this part. Always verify compatibility with your specific vehicle year, make, model, and trim level before ordering. Check the live compatibility chart on the product page for the most current fitment information.
OE Part Number Cross-Reference and Specifications
The APDTY 137292 replaces the following OEM and aftermarket part numbers:
- GM: 96626078, 19208998, 19256115, 19299535, 15837060, 95202871
- Suzuki: 56210-78J00, 56210-78J01, 56210-7
- Aftermarket: 695-987, 2ABS0803, ALS1748
This sensor is designed as a direct fit replacement, requiring no modifications for installation on compatible vehicles. It connects to the factory wiring harness and mounts in the original sensor location at the front wheel hub or knuckle assembly.
How Do You Replace a Front ABS Wheel Speed Sensor?
Replacing a front ABS wheel speed sensor is a straightforward repair that most DIYers and technicians can complete with basic hand tools. Here is a general overview of the process:
- Safety first: Park on level ground, set the parking brake, and chock the rear wheels. Disconnect the negative battery cable if working near electrical connectors.
- Raise and support the vehicle: Use a floor jack and jack stands rated for your vehicle's weight. Never work under a vehicle supported only by a jack.
- Remove the wheel: Take off the front wheel on the side being serviced to access the sensor.
- Locate the sensor: The wheel speed sensor is typically mounted to the steering knuckle or brake backing plate near the wheel hub.
- Disconnect the wiring: Unplug the electrical connector, noting any retaining clips along the harness routing.
- Remove the old sensor: Remove the mounting bolt (typically one bolt) and carefully pull the sensor from its bore. The sensor tip may have debris buildup.
- Clean the mounting area: Remove any rust, dirt, or metal shavings from the sensor bore and tone ring (toothed reluctor ring on the hub or axle).
- Install the new sensor: Insert the APDTY 137292 sensor into the bore, ensuring proper seating. Torque the mounting bolt to factory specification (typically 80-100 in-lbs, but consult your service manual).
- Reconnect wiring: Plug in the connector and secure any harness clips.
- Reinstall the wheel: Torque lug nuts to specification in a star pattern.
- Clear codes and test: Use a scan tool to clear ABS fault codes. Test drive the vehicle and verify the ABS and traction control lights are off.
Note: This is a general guide. Always consult a factory service manual or reliable repair database for vehicle-specific torque specs, procedures, and precautions.
Frequently asked questions
Can I replace just one front wheel speed sensor, or do I need to replace both?
You typically only need to replace the failed sensor. If only one front sensor has failed and the other is working properly, there's no need to replace both. However, if both front sensors are old and one has failed, some technicians choose to replace both as preventive maintenance.
Will the APDTY 137292 work on both the driver and passenger side?
Yes. This sensor is designed to fit either the front left or front right position on compatible vehicles. The sensor design is the same for both sides on these models.
Do I need to program or calibrate the sensor after installation?
No programming is required for a wheel speed sensor. After installation, clear any stored ABS fault codes with a scan tool, then drive the vehicle 10-15 mph for a short distance to allow the ABS module to relearn the sensor signals. The ABS light should turn off once the system verifies proper operation.
What if my ABS light stays on after replacing the sensor?
If the light remains on, scan for codes to diagnose the issue. Possible causes include a damaged tone ring (reluctor ring), debris on the sensor tip, incorrect sensor installation, damaged wiring, or a fault in another ABS component such as a different wheel sensor or the ABS module itself.
A failed front wheel speed sensor is more than an inconvenience—it disables critical safety systems designed to help you maintain control during emergency braking. The APDTY 137292 ABS wheel speed sensor provides a direct-fit, quality replacement for 2007-2015 Chevrolet, Pontiac, Saturn, and Suzuki models, restoring ABS and traction control function at a fraction of dealer cost. If your ABS light is on and diagnostic codes point to a front wheel speed sensor circuit fault, this sensor offers a reliable fix backed by OE-equivalent design and function. Verify fitment with your specific vehicle, follow proper installation procedures, and get your ABS system back to full operation.