The APDTY 100588 Manual Transmission Clutch Release Cable (LRC226) is a direct-replacement part designed to restore proper clutch pedal operation in select Dodge Caravan and Plymouth Voyager minivans equipped with manual transmissions. When your original cable stretches, frays, or binds, this cable returns smooth engagement and disengagement, eliminating stiff pedal feel, slipping clutch symptoms, and the risk of being stranded with a snapped cable.
Key Takeaways
- Direct replacement for 1992-1994 Dodge Caravan and Plymouth Voyager with manual transmission
- Replaces OE part numbers 4505534, 4511098, and 4670059
- Fixes stiff clutch pedal, inconsistent engagement, and cable binding issues
- Brand-new cable assembly with proper length and end fittings for correct routing
- Restores factory clutch pedal feel and prevents unexpected cable failure
Buy APDTY 100588 directly from APDTY
What Does the APDTY 100588 Clutch Release Cable Do?
The clutch release cable mechanically connects your clutch pedal to the clutch release fork at the transmission bell housing. When you press the clutch pedal, the cable pulls the release fork, which in turn pushes the release bearing against the pressure plate fingers to disengage the clutch disc from the flywheel. This action allows you to shift gears smoothly without grinding or damage.
Over time and tens of thousands of pedal cycles, the inner cable wire can fray, stretch, or corrode inside its housing. The plastic liner may wear, increasing friction and causing the pedal to feel stiff or spongy. In severe cases, the cable can snap entirely, leaving you unable to disengage the clutch—and unable to shift or drive the vehicle safely.
The APDTY 100588 is engineered to OE specifications, ensuring correct cable length, end-fitting geometry, and housing diameter for a precise fit and smooth operation in the vehicles listed below.
Which Vehicles Are Compatible with APDTY 100588?
This clutch release cable is confirmed to fit the following vehicles equipped with a manual transmission:
- 1992 Dodge Caravan (manual transmission)
- 1993 Dodge Caravan (manual transmission)
- 1994 Dodge Caravan (manual transmission)
- 1992 Plymouth Voyager (manual transmission)
- 1993 Plymouth Voyager (manual transmission)
- 1994 Plymouth Voyager (manual transmission)
Note: The vast majority of Caravan and Voyager models from this era were sold with automatic transmissions. If your vehicle has a manual transmission, verify your current cable's condition and compare the OE part numbers below. Always check the live compatibility chart on the product page for your specific year, make, model, and transmission type before ordering.
What Are the Symptoms of a Failing Clutch Cable?
A worn or damaged clutch release cable will cause noticeable drivability and pedal-feel issues:
- Stiff or hard clutch pedal: Increased friction from a frayed inner wire or dried housing makes the pedal difficult to press.
- Spongy or inconsistent pedal feel: Cable stretch causes vague engagement points and inconsistent clutch actuation.
- Clutch slipping or not fully disengaging: A stretched cable may not pull the release fork far enough, causing grinding when shifting or clutch slip under load.
- Pedal stuck to the floor or won't return: A broken inner wire or jammed housing prevents the pedal from returning to its rest position.
- Visible fraying or corrosion: Inspect the cable ends and housing for rust, kinks, or broken wire strands.
Replacing the cable at the first sign of trouble prevents being stranded and avoids potential damage to the clutch assembly, release bearing, or transmission input shaft.
OE Cross-Reference and Specifications
The APDTY 100588 replaces the following factory Mopar part numbers:
| OE Part Number | Notes |
|---|---|
| 4505534 | Original equipment Mopar number |
| 4511098 | Superseded Mopar number |
| 4670059 | Superseded Mopar number |
Additional Specifications:
- APDTY Part Number: 100588
- Alternate Reference: LRC226
- Condition: Brand new
- Application: Manual transmission clutch release cable
- Fitment: 1992–1994 Dodge Caravan / Plymouth Voyager with manual transmission
This cable is designed to meet or exceed OE specifications for durability, corrosion resistance, and smooth operation.
General Installation Overview and Safety Notes
Replacing a clutch release cable is a moderate-skill DIY job that typically requires basic hand tools and about 1–2 hours. Always consult a factory service manual or repair guide for your specific vehicle before beginning work.
General Steps:
- Disconnect the battery negative terminal and ensure the vehicle is on level ground with the parking brake set.
- Locate the cable at the transmission bell housing. Release the cable end from the clutch release fork, noting the routing and any clips or brackets.
- Inside the cabin, remove the lower dash panel or knee bolster to access the clutch pedal assembly. Disconnect the cable end from the pedal arm and note how the cable passes through the firewall grommet.
- Remove the old cable by pulling it through the firewall, unclipping any retainers along the engine bay routing path.
- Route the new APDTY 100588 cable along the same path, ensuring it does not contact hot exhaust components, sharp edges, or moving suspension parts.
- Attach the cable to the clutch pedal arm and secure the firewall grommet. Reinstall any dash panels.
- Connect the transmission end to the release fork and adjust cable free-play per the factory specification (typically 1/2" to 1" of free pedal travel before resistance is felt).
- Test the clutch pedal for smooth operation and proper engagement/disengagement before driving.
Safety Warnings:
- Never work under a vehicle supported only by a jack; use jack stands.
- Wear safety glasses and gloves to protect against sharp cable ends and debris.
- Ensure the transmission is in neutral and the parking brake is engaged before testing the clutch pedal.
- If you are not confident in your mechanical skills, have a qualified technician perform the installation.
Frequently asked questions
Will APDTY 100588 fit my 1993 Dodge Grand Caravan?
This cable fits 1992–1994 Dodge Caravan models with a manual transmission. If your Grand Caravan has a manual transmission and matches those years, it should fit, but always verify on the live compatibility chart since most Grand Caravans came with automatics.
Can I lubricate my old clutch cable instead of replacing it?
Lubrication may temporarily ease a stiff cable, but if the inner wire is frayed or stretched, lubrication won't restore proper function or prevent cable failure. Replacement is the safest and most reliable solution.
How do I know if my clutch problem is the cable or the clutch itself?
If the pedal feels stiff, spongy, or inconsistent and you can see or feel cable damage, the cable is likely the issue. If the pedal feels normal but the clutch slips under power or chatters on engagement, the clutch disc or pressure plate may be worn.
What tools do I need to replace the clutch cable?
You'll typically need basic hand tools: wrenches, sockets, pliers, and screwdrivers. A flashlight and a trim removal tool are helpful for accessing the pedal area and routing the cable through tight spaces.
The APDTY 100588 Manual Transmission Clutch Release Cable is the direct-fit solution for restoring smooth, reliable clutch pedal operation in 1992–1994 Dodge Caravan and Plymouth Voyager models with manual transmissions. By replacing a worn, stretched, or frayed cable with a brand-new OE-quality part, you eliminate stiff pedal feel, inconsistent engagement, and the risk of a roadside breakdown. Whether you're a DIY enthusiast or a professional technician, this cable offers the correct length, proper end fittings, and durable construction to get your manual-transmission minivan back on the road with confidence. Check the live fitment chart, confirm your vehicle's compatibility, and restore your clutch system today.