The APDTY 042513 door lock actuator with integrated latch is a direct-replacement unit for the front right (passenger-side) door on select 2002–2010 Scion and Toyota models. This integrated assembly combines the electric lock motor and mechanical latch in one housing, eliminating the clicking, binding, or total lock failure that occurs when the OE actuator motor wears out or the latch mechanism breaks.
Key Takeaways
- APDTY 042513 is an integrated door lock actuator and latch assembly for the front right (passenger) door
- Fits 2005–2010 Scion tC, 2004–2006 Scion xA, 2002–2006 Toyota Camry, 2003–2008 Corolla, 2003–2008 Matrix, and 2006–2010 Sienna
- Replaces Toyota OE part numbers 69030-02130, 69030-33221, and 69030-AA050
- Restores power lock operation and fixes doors that won't lock, unlock, or latch securely
- Brand new aftermarket unit; installation requires door panel removal and latch rod connection
Buy APDTY 042513 directly from APDTY
What Does the Door Lock Actuator and Latch Assembly Do?
The door lock actuator is a small electric motor inside each door that moves the lock rod up and down when you press the key fob, interior lock button, or door switch. On many Toyota and Scion models, the actuator is integrated into the same housing as the door latch—the mechanical catch that holds the door closed. When you pull the interior or exterior handle, the latch releases and the door opens.
The APDTY 042513 integrated unit combines both functions: it locks and unlocks the door electrically and latches the door mechanically. Because the motor and latch share a single assembly, failure of either component typically requires replacement of the entire unit.
What Are the Symptoms of a Failing Door Lock Actuator or Latch?
A worn or broken actuator/latch produces clear warning signs:
- Door won't lock or unlock remotely – The key fob or master lock button operates other doors but not the front right door.
- Clicking, grinding, or buzzing noise – The motor runs but the lock rod doesn't move, often due to stripped gears or a jammed mechanism.
- Door won't latch or stays ajar – The latch pawl is broken or bent, so the door won't stay closed or the dash warning light remains on.
- Intermittent operation – The door locks or unlocks only sometimes, indicating worn contacts or a binding actuator.
- Manual lock button doesn't move smoothly – The linkage feels stiff, stuck, or disconnected.
These symptoms often worsen in cold weather, when lubricant thickens and plastic gears become brittle. A failing actuator can also drain the vehicle battery if the motor continuously cycles or stalls under load.
Which Vehicles Does APDTY 042513 Fit?
This integrated door lock actuator and latch is designed for the front right (passenger-side) door on the following vehicles:
| Make | Model | Years |
|---|---|---|
| Scion | tC | 2005, 2006, 2007, 2008, 2009, 2010 |
| Scion | xA | 2004, 2005, 2006 |
| Toyota | Camry | 2002, 2003, 2004, 2005, 2006 |
| Toyota | Corolla | 2003, 2004, 2005, 2006, 2007, 2008 |
| Toyota | Matrix | 2003, 2004, 2005, 2006, 2007, 2008 |
| Toyota | Sienna | 2006, 2007, 2008, 2009, 2010 |
Always verify fitment using the live compatibility chart on the product page, as trim packages, production dates, and equipment variations may affect installation. This part number is not universal; it is vehicle-specific and will not fit other door positions or model years outside the list above.
Specifications and OE Cross-Reference
| APDTY Part Number | 042513 |
| Position | Front Right (Passenger-Side) |
| Assembly Type | Integrated Actuator and Latch |
| Condition | Brand New Aftermarket |
| Replaces Toyota OE Numbers | 69030-02130 69030-33221 69030-AA050 |
This assembly includes the latch mechanism, actuator motor, electrical connector, and mounting points. Lock rods, exterior handle, and interior trim clips are reused from the original door hardware.
Installation Overview and Best Practices
Replacing an integrated door lock actuator and latch requires interior door panel removal and careful handling of lock rods and electrical connectors. Follow these general steps:
- Disconnect the battery negative terminal to prevent electrical shorts and accidental power window or lock activation.
- Remove the door panel – Pry out trim covers, remove screws, and carefully release retaining clips. Disconnect the power window switch and any courtesy light connectors.
- Peel back the vapor barrier – This plastic or foam sheet protects the door cavity from moisture; be careful not to tear it.
- Disconnect lock rods and electrical connector – Note the routing and position of each rod (lock knob, exterior handle, interior handle) before unclipping them from the old latch.
- Remove mounting fasteners – Typically three bolts or Torx screws secure the latch to the door edge.
- Install the new APDTY 042513 assembly – Position the unit, tighten bolts to factory torque (typically 7–9 ft·lbs), reconnect rods and wiring, and verify the latch engages the striker when the door closes.
- Test operation before reassembly – Reconnect the battery and check lock/unlock function from the key fob, door switches, and manual lock button. Open and close the door several times to confirm smooth latching.
- Reinstall the vapor barrier and door panel – Use new adhesive or trim clips as needed, and torque panel fasteners evenly to avoid cracking.
Tools required: Phillips and flat-blade screwdrivers, trim panel removal tools, 10 mm socket or wrench, Torx driver set (T30 or T40 common), electrical contact cleaner, and dielectric grease for connectors. Refer to a factory service manual or vehicle-specific repair guide for torque specifications, wiring diagrams, and special procedures.
Why Choose APDTY 042513 Over OE or Used Parts?
Genuine Toyota/Scion actuator-latch assemblies can cost two to three times the price of quality aftermarket units, and availability is often limited for older models. Used or salvage-yard parts may have similar wear or hidden damage, leading to repeat failure within months.
The APDTY 042513 offers several advantages:
- Brand new construction – Fresh gears, motor, and latch pawl with no prior wear.
- Direct OE fit – Uses factory mounting points, electrical connectors, and lock-rod attachment points for a bolt-in installation.
- Cost-effective – Delivers OE-equivalent performance at a fraction of the dealer price.
- Ready to install – Integrated design eliminates the need to source and assemble separate actuator and latch components.
For DIY mechanics and independent repair shops, this part provides a reliable, economical solution to restore secure door operation and power lock convenience.
Frequently asked questions
Does APDTY 042513 fit the driver-side (left) door?
No. This assembly is designed exclusively for the front right (passenger-side) door. A separate part number is required for the driver-side door on these vehicles.
Can I use this part on a 2009 Toyota Corolla front left door?
No. APDTY 042513 is for the front right door only. Even though the 2009 Corolla is within the model year range, you must order the correct left-side part number for the driver door.
Do I need to program or calibrate the actuator after installation?
No programming is required. Once installed and connected, the actuator operates through the vehicle's existing body control module and lock circuits with no additional setup.
Will this fix a door that won't stay closed?
Yes, if the latch mechanism is the cause. A broken or worn latch pawl prevents the door from engaging the striker. Replacing the integrated actuator-latch assembly restores both the lock function and the mechanical door catch.
The APDTY 042513 integrated door lock actuator and latch is the direct-fit solution for front right door lock and latch failures on 2002–2010 Scion tC, xA, and select Toyota Camry, Corolla, Matrix, and Sienna models. By replacing worn gears, a failed motor, or a broken latch in one step, this assembly restores secure door closure and reliable power lock operation. Whether you're a DIY owner tired of manually locking a stubborn door or a technician seeking a cost-effective OE-equivalent replacement, APDTY 042513 delivers the quality and fit you need. Verify your vehicle compatibility on the product page, order with confidence, and get your passenger door working like new again.