The APDTY 022213 Throttle Body Actuator Motor is a cost-effective replacement for failed Ford throttle actuators that includes an integrated Throttle Position Sensor (TPS). Instead of replacing the entire throttle body assembly as dealerships typically require, this component allows you to repair only the failed actuator motor, saving hundreds of dollars while restoring proper throttle control and eliminating drive-by-wire system faults.
Key Takeaways
- Replaces the throttle actuator motor only, not the entire throttle body assembly
- Includes integrated Throttle Position Sensor (TPS) for complete repair
- Replaces numerous Ford OE part numbers including 3L2Z-9E926-AB, 5L2Z-9E926-A, 6R3Z-9E926-AA, and more
- Direct replacement for Ford vehicles with electronic throttle control systems
- Significantly more affordable than replacing the complete throttle body assembly
Buy APDTY 022213 directly from APDTY
What Does the Throttle Body Actuator Motor Do?
The throttle body actuator motor is the electronic component inside your throttle body that physically opens and closes the throttle plate in response to accelerator pedal input. In modern Ford vehicles equipped with electronic throttle control (also called drive-by-wire), there is no direct mechanical cable connecting your gas pedal to the throttle body. Instead:
- The accelerator pedal position sensor sends a signal to the engine control module (ECM)
- The ECM calculates the desired throttle opening based on pedal position, engine load, and other factors
- The ECM commands the throttle actuator motor to rotate the throttle plate to the precise angle needed
- The Throttle Position Sensor (TPS) provides feedback to the ECM confirming the actual throttle plate position
When the actuator motor fails, this entire system breaks down, leaving you with erratic throttle response, reduced power, or a vehicle that won't accelerate properly. The APDTY 022213 restores this critical control function by replacing the failed motor and TPS assembly.
What Are the Symptoms of a Failed Throttle Body Actuator?
A failing or failed throttle body actuator motor typically produces several recognizable symptoms:
- Check Engine Light: Diagnostic trouble codes (DTCs) such as P2100, P2101, P2106, P2107, P2108, P2110, P2111, P2112, P2118, or P2119 related to throttle actuator control system malfunction
- Reduced Engine Power Mode: Vehicle enters limp mode with severely limited acceleration to protect the engine
- Poor Throttle Response: Delayed, jerky, or unpredictable acceleration when pressing the gas pedal
- Engine Stalling: Engine may stall at idle or when coming to a stop
- Rough or Unstable Idle: RPM fluctuations or hunting at idle
- Intermittent Acceleration Problems: Throttle may work normally sometimes and fail other times, especially after cold starts or hot restarts
If you're experiencing these symptoms and diagnostic codes point to throttle actuator issues, the APDTY 022213 provides a targeted repair solution without the expense of a complete throttle body replacement.
Which Ford Part Numbers Does APDTY 022213 Replace?
The APDTY 022213 Throttle Body Actuator Motor is engineered to replace the following Ford OE part numbers:
| Ford OE Part Number | Notes |
|---|---|
| 3L2Z-9E926-AB | Original Equipment |
| 3L5Z-9E926-AD | Superseded OE Number |
| 5L2Z-9E926-A | Superseded OE Number |
| 5R3Z-9E926-EA | Superseded OE Number |
| 6C3Z-9E926-AA | Superseded OE Number |
| 6L2Z-9E926-C | Superseded OE Number |
| 6L3Z-9E926-A | Superseded OE Number |
| 6R3Z-9E926-AA | Complete Throttle Body Assembly |
| 7R3Z-9E926-AA | Superseded OE Number |
| 8L2Z-9E926-A | Superseded OE Number |
| 8L3Z-9E926-A | Superseded OE Number |
| 8L3Z-9E926-B | Superseded OE Number |
| 9C3Z-9E926-B | Superseded OE Number |
| 9R3Z-9E926-A | Superseded OE Number |
| 9R3Z-9E926-B | Superseded OE Number |
| 9W7Z-9E926-A | Superseded OE Number |
| 9W7Z-9E926-B | Superseded OE Number |
Important: Ford dealers typically sell only the complete throttle body assembly (part number 6R3Z-9E926-AA). The APDTY 022213 allows you to replace just the actuator motor component, which is the most common failure point, at a fraction of the cost. If your entire throttle body is damaged or you need the complete assembly, APDTY also stocks part number 6R3Z-9E926-AA.
What Vehicles Does the APDTY 022213 Fit?
The APDTY 022213 Throttle Body Actuator Motor is designed for Ford vehicles equipped with electronic throttle control systems. This component fits multiple Ford car, truck, and SUV models across various model years.
To verify exact fitment for your specific vehicle: Please use the live vehicle compatibility chart on the APDTY product page before purchasing. The compatibility chart will confirm whether this throttle actuator motor is the correct part for your year, make, model, and engine configuration. Fitment depends on your vehicle's specific throttle body design and the OE part number originally installed.
You can also cross-reference your vehicle's existing Ford part number (stamped on the throttle body or listed in your service records) against the replacement part numbers listed above to confirm compatibility.
Installation Overview and Considerations
Replacing the throttle body actuator motor requires moderate mechanical skill and some specialized knowledge of electronic throttle systems. Here's a general overview of the process:
- Disconnect the Battery: Always disconnect the negative battery terminal before working on any electronic engine control components
- Access the Throttle Body: Remove the air intake duct and any components blocking access to the throttle body
- Disconnect Electrical Connectors: Carefully unplug the electrical connectors from the throttle body
- Remove the Actuator Motor: Remove the mounting screws securing the actuator motor to the throttle body housing
- Install the APDTY 022213: Position the new actuator motor with TPS, ensuring proper alignment of the drive gear with the throttle plate shaft
- Secure and Reconnect: Torque mounting screws to specification, reconnect electrical connectors, and reinstall air intake components
- Relearn Procedure: Most Ford vehicles require a throttle body relearn or idle relearn procedure after replacement; this typically involves key-on cycles or using a scan tool to command the ECM to relearn throttle parameters
- Clear Codes and Test: Use a diagnostic scan tool to clear any stored trouble codes, then test drive to verify proper operation
Important Notes: Some throttle bodies may require careful cleaning of carbon deposits before installing the new actuator. Do not use harsh solvents on electronic components. Always consult a factory service manual for your specific vehicle for torque specifications and relearn procedures. If you're not comfortable working with electronic engine control systems, professional installation is recommended.
Technical Specifications
| Specification | Details |
|---|---|
| APDTY Part Number | 022213 |
| Component Type | Throttle Body Actuator Motor with Integrated TPS |
| Condition | Brand New |
| Application | Ford Electronic Throttle Control Systems |
| Included Components | Actuator Motor, Throttle Position Sensor (TPS) |
| Replaces OE Numbers | See full list of 17 Ford part numbers above |
| Repair Type | Component-level replacement (actuator only, not complete throttle body) |
| Installation Type | Direct replacement, requires relearn procedure |
Frequently asked questions
Can I replace just the actuator motor instead of the entire throttle body?
Yes, that's exactly what the APDTY 022213 is designed for. Ford dealers typically sell only the complete throttle body assembly, but in most cases, only the actuator motor fails. This component allows you to repair just the failed part, saving significant cost compared to complete throttle body replacement.
Does the APDTY 022213 include the Throttle Position Sensor?
Yes, the APDTY 022213 includes an integrated Throttle Position Sensor (TPS) along with the actuator motor. This ensures complete replacement of all electronic components that commonly fail in the throttle actuator assembly.
Will I need a scan tool to install this throttle actuator motor?
While basic installation can be completed with hand tools, most Ford vehicles require a throttle body relearn procedure after replacement. Some vehicles can complete this through a series of key-on cycles, but others may require a diagnostic scan tool to command the relearn process and clear trouble codes. Check your vehicle's service manual for the specific relearn procedure.
How do I know if I need the actuator motor or the complete throttle body assembly?
If diagnostic codes point to throttle actuator control system faults (P2100-series codes) and there's no physical damage to the throttle body housing, you likely need only the actuator motor (APDTY 022213). If the throttle body housing is cracked, the throttle plate shaft is damaged, or there's coolant contamination inside the body, you may need the complete assembly (APDTY part 6R3Z-9E926-AA).
The APDTY 022213 Throttle Body Actuator Motor with integrated TPS provides a cost-effective, component-level repair solution for Ford vehicles experiencing electronic throttle control problems. By replacing only the failed actuator motor instead of the entire throttle body assembly, you can restore proper throttle response and eliminate check engine lights at a fraction of dealer repair costs. This direct-fit replacement covers 17 different Ford OE part numbers and includes everything needed to complete the throttle actuator repair. Verify your vehicle's compatibility using the fitment chart on the APDTY product page, and restore reliable throttle control to your Ford vehicle today.