The APDTY 012548 power window switch is a black, single-button replacement designed to restore function to failing window controls in the front-right, rear-left, or rear-right door positions across a wide range of 1997–2009 Chrysler, Dodge, Jeep, and Ram vehicles. This direct-fit switch solves common problems like unresponsive windows, intermittent operation, or complete failure of individual passenger-side or rear window controls, replacing OE part numbers 56007695AC and 56007695AB.
Key Takeaways
- Direct replacement for front-right, rear-left, and rear-right window switches in select 1997–2009 Chrysler, Dodge, Jeep, and Ram models
- Single-button design in black finish, replaces Mopar 56007695AC and 56007695AB
- Fixes symptoms including non-responsive windows, intermittent operation, and stuck window glass
- Direct plug-and-play installation with factory connectors—no splicing required
- Always verify exact fitment using the live compatibility chart before purchase
Buy APDTY 012548 directly from APDTY
What Does the APDTY 012548 Power Window Switch Control?
The APDTY 012548 is a single-button power window switch that controls one window motor in your vehicle. Unlike multi-button master switches found on the driver's door, this switch is designed for:
- Front-right (passenger-side front) door panel
- Rear-left (driver-side rear) door panel
- Rear-right (passenger-side rear) door panel
When you press the rocker, the switch sends 12-volt current to the window motor, allowing the glass to rise or fall. Over time, internal contacts wear out from repeated cycling, heat, and moisture intrusion, leading to switch failure and loss of window control.
What Are the Symptoms of a Failing Power Window Switch?
A worn or damaged window switch exhibits these common signs:
- Window does not respond when you press the switch button
- Intermittent operation—window moves only occasionally or requires repeated presses
- Window moves in only one direction (up or down, but not both)
- Clicking sound from the switch with no window movement (motor may be fine)
- Burnt smell or melted plastic around the switch bezel, indicating overheating contacts
If the window motor runs when you swap the switch connector or use a different switch, the switch itself—not the motor or regulator—is the problem. Replacing the switch is often the fastest, most cost-effective repair.
Which Vehicles Are Compatible With APDTY 012548?
According to verified fitment data, the APDTY 012548 power window switch is compatible with the following vehicles in the front-right, rear-left, and rear-right positions (black, 1-button configuration):
| Make | Model | Year Range |
|---|---|---|
| Chrysler | 300M | 1999–2004 |
| Chrysler | Concorde | 1998–2004 |
| Chrysler | LHS | 1999–2001 |
| Chrysler | Sebring | 2001–2006 |
| Dodge | Dakota | 2000–2004 |
| Dodge | Durango | 1998–2003 |
| Dodge | Intrepid | 1998–2004 |
| Dodge | Ram 1500 | 2002–2009 |
| Dodge | Ram 2500 | 2002–2009 |
| Dodge | Ram 3500 | 2002–2009 |
| Dodge | Ram 4500 | 2002–2009 |
| Dodge | Ram 5500 | 2002–2009 |
| Dodge | Stratus | 2001–2006 |
| Jeep | Cherokee | 1997–2001 |
Important: This fitment applies only to vehicles originally equipped with single-button switches in these door positions. Some trim levels or cab configurations may differ. Always check the live compatibility chart on the product page to confirm your exact year, make, model, and door location before ordering.
APDTY 012548 Specifications and OE Cross-Reference
| Part Number | APDTY 012548 |
| Type | Single-button rocker switch |
| Color | Black |
| Position | Front Right / Rear Left / Rear Right |
| OE Replacement For | 56007695AC, 56007695AB |
| Connector | Factory plug, direct fit |
| Material | ABS plastic housing, internal copper contacts |
This switch is engineered to match OEM form, fit, and function, ensuring reliable operation and straightforward installation without modification.
How to Install the APDTY 012548 Power Window Switch
Replacing a power window switch is a straightforward DIY task that typically takes 10–20 minutes per door. Follow these general steps:
- Disconnect the battery negative terminal to eliminate risk of short circuits.
- Remove the interior door panel: Unscrew any visible fasteners (usually behind trim caps), gently pry off retaining clips with a trim tool, and lift the panel free of the window sill.
- Locate the window switch: It will be clipped or screwed into the door panel armrest or switch bezel.
- Disconnect the wiring harness: Press the release tab and pull the connector straight off the back of the old switch.
- Remove the old switch: Unclip or unscrew it from the door panel.
- Install the APDTY 012548: Snap or screw the new switch into place, ensuring it sits flush and secure.
- Reconnect the wiring harness: Push the connector onto the new switch until it clicks.
- Test operation: Before reinstalling the door panel, reconnect the battery and test the window up and down several cycles.
- Reinstall the door panel: Align clips, press firmly, and replace all screws and trim caps.
Safety tip: Keep fingers clear of the window track during testing. If the window still does not operate, inspect the motor, regulator, and wiring for additional faults.
Why Choose the APDTY 012548 Over Aftermarket Alternatives?
The APDTY 012548 offers several advantages for DIY mechanics and professional technicians:
- OE-equivalent quality: Designed to meet or exceed original equipment specifications for durability and fit.
- Direct plug-and-play: Factory-style connector eliminates the need for wiring splices or adapters.
- Wide vehicle coverage: One part number serves multiple Chrysler, Dodge, Jeep, and Ram models from 1997 to 2009.
- Cost-effective repair: Replacing only the failed switch—rather than the entire master switch assembly—saves both time and money.
- Black finish: Matches OEM interior trim for a clean, factory appearance.
By restoring reliable window operation, the APDTY 012548 improves driver and passenger convenience, ventilation control, and overall vehicle usability.
Frequently asked questions
Does the APDTY 012548 fit the driver-side master switch location?
No. The 012548 is a single-button switch for front-right, rear-left, and rear-right door positions only. Driver-side master switches (which control multiple windows) require a different part number.
Will this switch work if my window motor is also bad?
The switch only sends electrical signals to the motor. If the motor itself is seized or burnt out, replacing the switch will not restore operation. Test the motor with direct 12V power to confirm it runs before replacing the switch.
Is the APDTY 012548 switch illuminated?
No. This is a non-illuminated, single-button rocker switch. Some original equipment switches in these positions also lack backlighting.
Can I use this switch in other door positions or vehicles not listed?
Only install the 012548 in the specified positions (front-right, rear-left, rear-right) for the vehicles listed in the compatibility chart. Using it in unlisted applications may result in connector mismatch or improper fit.
The APDTY 012548 power window switch delivers a direct-fit, cost-effective solution to restore window control in front-right, rear-left, and rear-right door positions across a broad range of 1997–2009 Chrysler, Dodge, Jeep, and Ram vehicles. By replacing worn OE part numbers 56007695AC and 56007695AB, this single-button switch eliminates intermittent operation, non-responsive windows, and the frustration of stuck glass. Always verify your exact year, make, model, and door location using the live compatibility chart before ordering, and enjoy the convenience of plug-and-play installation with factory connectors. Restore reliable window operation today with APDTY 012548.